NuOutlet-LN User’s Manual USM Ver 1.1
10static IP "192.168.1.8" on the LCD and restores factory settings when Chassis ID and Slot ID are both turned to F. d) Chassis ID – Ide
11Right 1. Outlet Power Supply – Plug in the power supply of the Device Under Test (DUT). The power supply can be switched on and off either thr
123.2 Upgrading Firmware The firmware of the NuOutlet-LN can be updated by following the instructions below: 1. Check the hardware version Help &
134. Software 4.1 Installation To configure the NuOutlet-LN, it is best to install the configuration software. Follow the instructions below: 1.
14 1. Enter the User Name and Organization. 2. Click the radio button to select current user or all users. 3. Click Next to continue. Click Cha
15 The installation screen is displayed. Once installation is finished, the following screen is displayed. Click Finish to close the window. Two
164.2 Uninstalling If applications do not work correctly, it may be necessary to uninstall them. 1. Insert the installation CD into the CD-ROM dr
17 Press Remove to uninstall the applications. The uninstallation is in progress. Once uninstallation is finished the following screen is dis
184.3 Updating Software Periodically Xtramus may update the NuDiscover and NuOutlet-LN Window software. 1. Before installing a new version of
195. Basic Usage 5.1 NuDiscover There are two ways to connect to the NuOutlet-LN: 1 – Directly through the NuOutlet-LN window if the IP address of
2Foreword Copyright Copyright © 2010 Xtramus Technologies, all rights reserved. The information contained in this document is the property of Xtram
205.2 NuOutlet-LN Window The NuOutlet-LN Window is used to configure all NuOutlet-LN devices 1 Open – Open saved configuration (.cfg) files. 7
215.3 NuOutlet-LN Information 1 Type – The type of device connected. 7 User Priority – Display who is logged in Administrator or Guest. 2 Name – N
225.4 Username and Password The NuOutlet-LN comes with 2 available user settings: 1. Administrator – Gives full read and write access to the NuOu
236. Connecting the Device 6.1 Cable Connection The NuOutlet-LN connects directly to the DUT. Follow the instructions below to ensure correct conn
246.2 Discovering Devices To start configuring devices, they must first be discovered; to do this, follow the instructions below: 1. Start the NuD
257. Functions 7.1 Setting IP address Each NuOutlet-LN is pre-configured with the following IP address [192.168.1.8]. To change this address, foll
263. Once logged in, the following screen will be displayed. 4. Press System > Set IP Configuration and the following window is displayed. Ch
277.2 Reporting 7.2.1 Interval Setting Intervals are the times between the points where data is gathered from the DUT. To access the Interval Setti
287.2.2 Show Statistics The statistics screen is the most important screen in the NuOutlet-LN application. It displays all information gathered fro
291 Open – Open previously saved log files in chart format 12Exit – Quit the counter chart 2 Save – Save files in .csv format to be opened in eit
3Revision History Date Version History 2007/12/25 1.0 First version 2010/12/17 1.1 1. Change manual format accordingly. 2. Change NuOutlet-Wi
307.2.3 Alarms Alarm Setting When the alarm is activated, it can either emit a sound or, if the device is powered by the NuOutlet-LN, switch the d
31Alarm Report When the alarm is detected, a report is generated; an example is shown below. Alarm setting could be carried out by pressing Settin
327.3 Chart Color Setting The counter chart is configurable so that its appearance and functionality can be altered for individual preferences.
33Cursor 1 – The value at the cursor 1 position. Click on any point in chart to change this value. Cursor 2 – The value at the cursor 2 position. P
347.3.2 Device Control NuOutlet-LN is capable of remotely controlling the power status and cycle reboot modes of the DUT device. 1. Press Control
35(i) Select Crossing Mode in different degrees or free run (any point) only in power on or off status. (ii) Click on Apply button to activate the
367.3.3 Colors In the chart below, each measurement is represented by a different color for clarity. The following selected and unselected curves
377.3.4 Vertical and Horizontal Axes Vertical Axis The vertical axis dial behaves like a zoom function, left click the mouse button to the desired
387.4 Saving and Loading Log Files 7.4.1 Auto Save The auto save function needs to be enabled before it comes into operation; to do this follow th
397.4.3 Loading Log Files To load a previously saved chart, follow the instructions below. 1. Either a) Press File > Load Log File, b) Press t
4Table of Contents Foreword ...
40 4. 8 additional fields are displayed to load log files for more details. 1 Set Chart Title – Name a title for this chart and also show in the c
417.5 Saving and Loading Configuration Files The configuration of the current file can be saved and loaded. The configuration file contains the fo
428. Default Settings The NuOutlet-LN can be reset to its default settings using the NuOutlet-LN Window: Press System > Reset to factory defaul
439. NuOutlet-LN Specifications NuOutlet-LN : AC Power Monitor and Controller Model No. NuOutlet-LN Connector 1 RJ45 Ethernet phone jack and 1 IE
44Weight Net Weight: 640g, Shipping Weight: 1450g Operating Temperature 32oF to 113oF (0oC to 45oC) Storage Temperature -40oF to 185oF (-40oC to
45 E-mail: [email protected]: www.Xtramus.comXTRAMUS TECHNOLOGIES®
46 Note: Information and specifications contained in this document are subject to change without notice. All products and company names are tradem
51. NuOutlet-LN Packet Accessories NuOutlet-LN comes with the following items to connect it to a DUT (Device under Test). Accessory Image Accesso
62. Safety Instructions 2.1 Overload Protection The NuOutlet-LN is fitted with 3 levels of protection to prevent the device being damaged in the ev
72.1.2 Internal Breaker The NuOutlet-LN is fitted with a breaker switch that will be activated when outlet power shortage occurs. 2.1.3 Power Fuse
83. Product 3.1 Description The NuOutlet-LN is designed for the collection of power parameters such as Vrms, Irms, active power, power factor, pea
93. Configuration Buttons a) V.A.W. – Press this button to switch the display between Volts, Amps and Watts and current operating temperature.
Commentaires sur ces manuels